f ig . b a k 3 d o n l y n ' c y g n g ' l i n e l f s w c 1 r l c y a d c 2 o l l ' a k 1 /4 w it h o u t p o w e r s w f ig . a a k 3 /4 o n l y n g i e n f l l s w r c 1 l c y n ' g ' c 2 o a d c y l ' l f o r tr a n s fo rm e rs w it h t w o s e p a ra te w in d in g s 1 1 0 v 1 1 0 v s w l ' f ig . c r n g i n e l l f c 1 l l o a d g ' c y c y n ' c 2 1 1 0 v 2 2 0 v 2 2 0 v 1 1 0 v 1 3 4 2 1. power module incorporates an iec connector, a fuse holder with optional power on/off switch and voltage selector switch, plus an emi filter all-in-one single, easy-to-install unit. 2. fuse holder designed for one iec 5x20mm fuse. safety interlock prevents fuse removal with line plug inserted (use only with 250v fuse). 3. all part numbers are ul recognized, csa certified and vde approved.4. switch electrical lifetime: 10,000 cycles. maximum inrush current: 70a. 1. maximum leakage current each line-to-ground @ 115v ac 60hz: 0.25ma @ 250vac 50hz: 0.45ma 2. hipot rating (one minute) line-to-ground: 2250vdc line-to-line: 1450vdc 3. operating frequency: 50/60hz 4. rated voltage: 115/250v ac current frequency-mhz rating .15 .50 1.0 5.0 10 30 3a 30 35 40 35 35 35 6a 16 25 30 42 45 40 3a 10 40 45 45 45 35 6a 6 25 30 42 45 40 common mode (l-g) in 50 ohm system differential mode (l-l) in 50 ohm system 4-1 e l e c t r i c a l s c h e m a t i c series specifications minimum insertion loss in db power entry module emi fil ters 1. single-pole ul, csa & vde approved current rating: ul & csa-6a both at 125v ac & 250vac; vde-6a at 250vac.2. double-pole ul csa & vde approved current rating: ul & csa-6a at 125v ac, 4a at 250vac; vde-4a at 250vac. 3. voltage selector sw -ul, csa & vde approved current rating: 10a at 125vac; 5a at 250vac. 4. voltage selector sw -ul, csa & vde approved current rating: ul & csa-6a both at 125v ac & 250vac; vde-6a at 250vac. delt a p art no. ak1 ak2 ak2d ak3 ak3d ak4 ak5 115v ac 6a 6a 6a 6a 6a 6a 6a rated current 250vac 6a 6a 4a 6a 4a 6a 6a iec connectorfuse holder 12 12 power switch sp dp sp dp 33 3 4 volt age selector sw rear rear rear front electrical schematic fig. a fig. a fig. b fig. a fig. b fig. a fig. c type & rated current introductions d v e p o w e r e n t r y m o d u l e f i l t e r s
i n c h m m u n i t : ak3,ak3d ak4 (without power switch) ak1 ak2,ak2d ak5 1 .1 5 2 9 .2 n l g 2.65 67.3 65.3 2 .2 4 5 6 .9 2.57 26.9 2 .1 7 5 5 .1 1.059 g 2 .6 0 6 6 .0 1 1 5 v 1 .1 5 2 9 .2 n l g 2.65 67.3 o i 1 6 .5 0 .6 5 26.9 1.059 g 2 9 . 2 1 . 1 5 n g 2.65 67.3 l 1 1 0 2 2 0 2 . 2 4 2 . 1 7 5 6 . 9 5 5 . 1 65.3 2.57 0 . 4 3 1 0 . 9 0 . 5 7 1 4 . 4 8 1 . 0 5 9 2 6 . 9 n g l 4 1 3 2 65.3 2.57 6 0 . 5 2 . 3 8 5 5 . 1 2 . 1 7 2 9 . 2 1 . 1 5 n g l o i 67.3 2.65 1 . 0 5 9 2 6 . 9 n l g 66.0 1.0 r0.04max. 2 7 . 0 2.6 0.003 1 . 0 6 3 0 . 0 0 3 4-2 suggested thickness of mounting panel is from 0.04 to 0.07 inch suggested mounting cutout mechanical construction p o w e r e n t r y m o d u l e f i l t e r s
|
